Doresoom

Huntsville, AL

Mechanical Engineer from Huntsville, AL.

top accounts reputation activity subscriptions

Automatically plot different colored lines

matlab plot matlab-figure asked Jan 8, 2010 at 16:01

stackoverflow.com

44 votes

Are there ways to determine if a wall is load bearing?

walls load-bearing structural asked Jul 21, 2010 at 19:16

diy.stackexchange.com

41 votes

Difference between MATLAB's numel and length functions

arrays matlab microbenchmark asked Jun 25, 2010 at 16:33

stackoverflow.com

35 votes

How can I revive a tree that's been stripped of bark?

trees tree-care asked Jun 8, 2011 at 18:37

gardening.stackexchange.com

33 votes

Is it worth spending extra to get a nicer circular saw?

tools product-recommendation saw asked Nov 5, 2010 at 18:37

diy.stackexchange.com

31 votes

Why does the Weasleys' clock have a dentist setting?

harry-potter movie wizards asked Jul 7, 2014 at 16:09

scifi.stackexchange.com

30 votes

Should I use nails or screws for hanging drywall on the ceiling?

drywall ceiling screws nails asked May 19, 2011 at 22:55

diy.stackexchange.com

25 votes

What grit sandpaper should I use between coats of polyurethane?

wood finishing sanding wooden-furniture polyurethane asked Feb 5, 2011 at 18:03

diy.stackexchange.com

21 votes

What are the different types of drywall anchors, and what are the advantages of each?

walls drywall anchor drywall-anchor hardware asked Jul 26, 2010 at 15:41

diy.stackexchange.com

21 votes

What's the most common cause of A/C refrigerant lines freezing?

hvac air-conditioning central-air asked Sep 12, 2011 at 16:45

diy.stackexchange.com

Top Answers

What are the tools that every Do-it-Yourselfer must own?

diy.stackexchange.com

MATLAB, Filling in the area between two sets of data, lines in one figure

stackoverflow.com

Is there a standard height and depth for stairs?

diy.stackexchange.com

When, if ever, is it safe to use gloves with power tools?

woodworking.stackexchange.com

How can I protect my fingers while using a band saw?

diy.stackexchange.com

How much load can a (wood) board support, if it is supported only at the ends?

diy.stackexchange.com

How do bench dogs work?

woodworking.stackexchange.com

Assign a value to a static text in GUI MATLAB

stackoverflow.com

What is the recommended home design software?

diy.stackexchange.com

Is it OK to drill vertically through a joist?

diy.stackexchange.com

Why did my installer install 1/4 round corners like this and how can I fix it?

diy.stackexchange.com

How do lawnmower blade sizes work?

diy.stackexchange.com

Why are homes wired using solid wire rather than stranded?

diy.stackexchange.com

Clone figure in Matlab - with properties and data

stackoverflow.com

Matlab: How to get the current mouse position on a click by using callbacks

stackoverflow.com

Can a gambrel roof have outer instead of inner supports?

diy.stackexchange.com

How do I prevent dangerous kickback on a table saw?

woodworking.stackexchange.com

How can I install crown cornice molding and trim on rounded outside corners?

diy.stackexchange.com

What is the best way to remove popcorn from the ceiling?

diy.stackexchange.com

Can I make a dado blade set out of multiple regular blades?

woodworking.stackexchange.com

Do I need an egress bedroom window if I have a walk-out exterior door?

diy.stackexchange.com

Who do I contact to have the property line marked?

diy.stackexchange.com

What are the "must do" tasks before winter hits?

diy.stackexchange.com

What is the best way to clean your clothes dryer exhaust?

diy.stackexchange.com

What are these white bugs that leave white stains on my cars and driveway?

gardening.stackexchange.com

Why are we instructed not to use manure before planting carrots?

gardening.stackexchange.com

How can I get rid of a mouse in my house?

diy.stackexchange.com

Why does our shower make a screaming noise?

diy.stackexchange.com

How do I know it's time to replace my circular saw blade?

woodworking.stackexchange.com

How can I determine the load capacity of a simple bench?

woodworking.stackexchange.com