Stack Exchange

apalopohapa

Self under construction.

top accounts reputation activity bookmarks subscriptions
Top Questions
18 votes

Will a 0402 0.01 µF ceramic capacitor next to a 0402 0.1 µF ceramic capacitor have any power decoupling benefits?

capacitor parallel ceramic decoupling asked Jan 19 '12 at 4:17
electronics.stackexchange.com

15 votes

How to retrieve part information from Digi-Key automatically

components bom asked Jul 7 '10 at 20:18
electronics.stackexchange.com

11 votes

USB 3.0 Hub shield connection

usb grounding shielding usb-hub asked Mar 6 '17 at 20:31
electronics.stackexchange.com

7 votes

Antenna matching network topology

antenna component-selection impedance-matching tuner asked Aug 21 '14 at 18:38
electronics.stackexchange.com

7 votes

Shutdown for LT3080 current source

current-source asked May 9 '10 at 3:08
electronics.stackexchange.com

7 votes

Is there any VHDL 93 or 2002 code that is incompatible with VHDL 2008?

vhdl simulation synthesizer asked Aug 17 '12 at 4:21
electronics.stackexchange.com

6 votes

How to avoid a ground loop between pcbs

analog groundloops asked Jan 8 '14 at 23:38
electronics.stackexchange.com

6 votes

Export restrictions when sourcing parts for PCB assembly in foreign country

components pcb-assembly sourcing regulations asked Jul 24 '14 at 7:09
electronics.stackexchange.com

5 votes

Why is 1000Base-T RJ-45 pinout scrambled instead of having each diff. pair in sequence ?

ethernet pinout asked Jan 19 '12 at 22:15
electronics.stackexchange.com

5 votes

For remoting 1000Base-T ethernet connector, is it better to remote PHY from magnetics or magnetics from connector?

connector ethernet remote magnetics asked Jan 19 '12 at 22:24
electronics.stackexchange.com


Top Answers
41
What is an LUT in FPGA?
electronics.stackexchange.com

18
Op Amp gain less than 1?
electronics.stackexchange.com

16
Altium layers “blacked out”
electronics.stackexchange.com

13
Which has better efficiency: step-up or step-down switching voltage regulator?
electronics.stackexchange.com

12
A decent library of component simulation, schematic and PCB layout?
electronics.stackexchange.com

12
Conditional stability
electronics.stackexchange.com

12
Why is Floating point non-synthesizable in verilog
electronics.stackexchange.com

12
Does this circuit regulate current?
electronics.stackexchange.com

11
Why would you attach a Diode to the base of a BJT?
electronics.stackexchange.com

10
Why is my instrumentation amplifier's gain non-linear?
electronics.stackexchange.com

9
What is the best tool to hold small printed circuit board?
electronics.stackexchange.com

8
Controlling MSP430 PWM with a Laptop
electronics.stackexchange.com

8
Run code once in lifetime of an embedded C program
electronics.stackexchange.com

7
Reasoning behind “neutral pin nearest the edge” rule of thumb?
electronics.stackexchange.com

7
Why is it ok to use polarized caps to remove DC offset from an audio input?
electronics.stackexchange.com

7
Number of gates in series
electronics.stackexchange.com

6
How can I make a plated-through hole in Eagle?
electronics.stackexchange.com

6
How does writing to output pins on PORTB affect RBIF interrupt on PIC16F877
electronics.stackexchange.com

6
Logic NOT gate only works with Oscilloscope probe connected
electronics.stackexchange.com

6
MCP3008 ADC , Reading 16 bits instead of 10 bits
electronics.stackexchange.com

6
Proper clock generation for VHDL testbenches
electronics.stackexchange.com

5
Why does the led turn dim gradually and then turn off when attached to a capacitor in series?
electronics.stackexchange.com

5
VHDL code compiling on quartus II
electronics.stackexchange.com

5
Circuit with switching MOSFET not working
electronics.stackexchange.com

5
MOSFET and clamp on I2C interface lines as level tranlastor
electronics.stackexchange.com

5
(How) can I run a microcontroller and DC motor from the same battery?
electronics.stackexchange.com

5
Is it valid to consider back-EMF in a DC motor equivalent to increased inductance?
electronics.stackexchange.com

5
Bootstrap circuit function
electronics.stackexchange.com

5
Set toggle rate in Quartus II
electronics.stackexchange.com

5
Eagle: Removing unwanted bits of copper pour
electronics.stackexchange.com

1 2